TOPCON:GT
2021年8月24日公開
※ TS側でPINコードが設定されていると、接続できない場合があります。
TSのPINコードは設定しないようにしてください。
接続方法 : Bluetooth
1 [設定]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-1.png)
2 [通信]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-2.png)
3 [ 通信モード ]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-3.png)
4 [通信モード]を「Bluetooth」に設定して[ENT]を押します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-4.png)
5 [ 通信タイプ]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-5.png)
6 [ Sタイプ]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-6.png)
7 次のように設定して[ENT]を押します。
チェックサム:「なし」
コントローラー:「全て」
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-7.png)
8 [Tタイプ]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-8.png)
9 次のように設定し[ENT]を押します。
出力タイプ:「REC-A」
デリミタ:「ETX」、トラックステート:「Off」
ACKモード:「Off」
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-9.png)
10 [PRG]を押します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-10.png)
11 [設定]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-11.png)
12 [観測条件]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-12.png)
13 [ サーチ/追尾 ]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-13.png)
14 次のように設定します。
自動視準:「高速」
測距動作:「自動追尾あり」
サーチ方法:「グローバルサーチ」
グローバルサーチパターン:「1」
鉛直角範囲:「15°」
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-14.png)
※RC(リモートキャッチャー)を使用する 場合は、
サーチ方法:「RC-コントローラー」
に設定します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-15.png)
15 画面を下にスクロールして、次のように設定し[ENT]を押します。
水平角範囲:「15°」
追尾測定:「スタンダード」
追尾予測時間:「2秒」
追尾ウェイト時間:「3600秒」
指定角旋回精度:「5“」
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-16.png)
16 [PRG]を押します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-17.png)
17 [ 観測 ]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-18.png)
18 観測を行います。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-19-2.png)
RECの設定
(TS側から出力する場合のみ設定します。)
※FIELD-TERRACEは「HVDアウトT」 (距離観測あり)のみ対応しています。
1 観測を行います。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-20.png)
2 [カスタマイズ]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-21-1.png)
3 [観測]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-22.png)
4 [操作アイコン]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-23.png)
5 操作アイコンを入れ替える位置を選択します。(下図例 「モーター」)
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-24.png)
6 [HVDアウトT]を選択します。
※「HVDアウトS」もあるので間違えないようにしてください。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-25.png)
7 [ESC]を押します。
([HVDアウトT]が選択されない場合は [ENT]を押してください。)
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-26.png)
8 [PRG]を押します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-27.png)
9 [観測]を選択します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-28.png)
10 [HVDアウトT]を選択して観測します。
![](https://const.fukuicompu.co.jp/user/products/fieldterrace/wp/wp-content/uploads/2021/08/3-29.png)